• About us
  • For partners
  • For consumers
  • Products
Ecosoft

Industrial reverse osmosis system Ecosoft MO-2

Article : MO22XLWE
  • Energy efficiency with Dow Filmtec™ XLE membranes and Grundfos pump 
  • Reliable performance with quality components and engineering 
  • Individual project evaluation per request 
  • CE marking for compliance with EC New Approach Directives 
  • ISO 9001 certified factory 
€14,100
14100

Ecosoft MO-2 is a fully automated 2…2,5 m3/h reverse osmosis system. The equipment includes Grundfos high pressure pump, Dow Filmtec™ extra low energy membranes, Danfoss automated valves and Honeywell flow control valves.

The RO system is equipped with a controller and most necessary instrumentation. A range of options is available on request. Ecosoft RO systems offer great value in the following applications.


         

Applications

 

Benefits

ico_boiler.png Steam boilers Less boiler blowdown compared to ion
exchange softened water
ico_semi.png
Semiconductor
manufacturing
Enhanced rejection of silica, boron, ammonia,
and other impurities compared to other
RO products
ico_pharma.png Pharmaceutical
manufacturing
Consistent rejection of pyrogens and toxic
constituents
ico_food.png Food processing Enhanced Dow Filmtec™ membranes and
raw water blending available optionally
ico_chem.png Chemical
manufacturing
Purified water is requisite for most processes
in chemical industry
ico_cooling.png Heat and
cooling circuits
Prevention of scaling and corrosion
due to hardness  and other impurities
ico_anod.png Galvanic and
electroplating
Used to obtain any grade of water for metal
finishing
ico_glass.png Insulation glazing Prevention of stains and scale on glass surfaces,
lower detergent usage
ico_textile.png Textile industry Used to obtain any grade of water for textile
process
ico_bottle.png Drinking water
bottling
Heavy duty Dow Filmtec™ membranes for
problem water with nitrate, ammonia, high TOC,
high TDS available as option
ico_irri.png Agriculture Demineralized water is most suitable for both
plants and irrigation systems
ico_fish.png Fish farms Optional raw water blending allows to fine tune
TDS, hardness, and alkalinity to specific
requirements
ico_building.png Utility water
treatment
RO water meets the EC Drinking Water
Directive and protects pipes and valves against
scaling, clogging and corrosion
ico_wash.png Laundry and
car wash
Prevention of stains and scale, cleaner
wash/laundry, lower detergent usage
ico_desal.png Desalination Dow Filmtec™ XLE membranes and Grundfos
Blueflux® pumps offer lowest energy use
per m3 permeate


Parameter

Amount

Value

Flow capacity 1 2 m3/h
Membrane elements Dow Filmtec™
XLE-440
2 pcs
Electrical specifications

400
50
V
Hz
Pump power 4 kW
Inlet pressure of water 2 2…4 bar
Operating pressure 7…10 bar
Maximum pressure 14 bar
Influent flow rate during service 2,5…4 m3/h
Influent flow rate during rinse 16…20 m3/h
Connection port sizes:
— feed water
— permeate
— concentrate

DN40
DN25
DN40

Dimensions (Height x Width x Depth)
— Overall
— Boxed

1.9×1.7×1.2
2.2×2.0×1.5

m
m
Weight
— Dry
— Cargo

400
520
 
kg
kg
Feed water requirements
— Total Dissolved Solids
— Hardness
— Iron
— Manganese
— Hydrogen Sulfide
— Silica
— Chlorine
— Silt Density Index
 
< 3000
< 150
< 0.1
< 0.05
none
< 20
< 0.1
< 5
 
mg/L (ppm)
mg/L CaCO3 (ppm CaCO3)
mg/L (ppm)
mg/L (ppm)
 
mg/L (ppm)
mg/L (ppm)

1 at 15 °C, 2000 mg/L feed water, ±10%

2 stable pressure (+/- 0.5 bar) in the specified range is required for steady operation of the system


Components of the system:

  • Dow Filmtec™ XLE membranes

  • Grundfos high pressure pump

  • Danfoss motorized valves

  • Multifunctional controller

  • Permeate conductivity sensor

  • Sediment filter

  • Low and high pressure switches

  • Float switch

  • Vibration resistant pressure gauges and rotameters

  • Frame with unique design


Optional:

  • Dow Filmtec™ ECO PRO and BW30HRLE membranes for problem water

  • Membrane rinse with permeate

  • Raw water blending


MO-2 dimensions.png

Operation:

Feed water goes through sediment prefilters to remove particles.
If using antiscalant for hard water then it is injected before the prefilters, so the chemical is mixed with water more thoroughly.
High pressure pump feeds the prefiltered water into the membrane array. Inside the membranes, feed water is separated into purified water (permeate) and brine with retained impurities (concentrate).
Ecosoft RO systems feature built-in concentrate recycle, sending part of the concentrate back to the pump. Recycle flow control and drain flow control work to sustain the operating pressure and the recycle/waste ratio.
Operating pressure is variable within allowed range. Higher pressure produces higher permeate flow rate and/or recovery. Proper operating pressure and recycle/waste must be set up during commissioning.
Ecosoft RO system runs in a completely automated fashion. The system stops to standby when pure water tank is full. Automated membrane rinse occurs every time before standby, with preprogrammed intervals during standby and service.
If any of below conditions occur, the system switches off and displays failure alert:
iso-exclamation-warning-symbol-is-2002(1).png low feed water pressure
iso-exclamation-warning-symbol-is-2002(1).png high operating pressure
iso-exclamation-warning-symbol-is-2002(1).png high permeate conductivity
iso-exclamation-warning-symbol-is-2002(1).png phase or voltage failure

Maintenance:

  1. changing out expendable filters in pre-filter housings
  2. chemical clean (CIP) the RO membranes when signs of membrane scaling or fouling arise; those include lower permeate flow rate or higher permeate conductivity 10% or more; normally, CIP lasts a few months before another CIP is required
  3. if CIP fails to restore membrane flux, the membrane elements need to be replaced;
  4. whenever an extended downtime is to happen, the membranes should be rinsed and soaked in preservative solution

Important precautions:

  • Carefully read the instruction before operating the unit.
  • Only use piping of equal or larger diameter than the RO system's inlet and outlet ports. Avoid long runs of small diameter pipe.
  • Only use equal or larger diameter point-of-entry filters to provide maximum influent water flow rate. 2,5×10 size filters only have up to 1-2 m³/h capacity (5-10 gpm) and should not be used for this Ecosoft RO system.
  • Membranes are shipped in original packaging and must be installed before operating the system. O-ring seals on the membranes must be on the feed water side of the pressure vessel.
  • Remove plastic wraps from filters before installing them in pre-filter housings.
  • Make sure feed water is supplied to the system at required pressure before starting up the system.
  • Check Lovato protection relay when connecting power to the cabinet. Red light or flashing green light signals phase failure or abnormal voltage conditions as per instruction.
  • Do not use brass, iron, or copper pipe for permeate plumbing.
  • During first run, concentrate flow rate, recycle flow rate, and the operating pressure must be adjusted with the flow control valves. The operating pressure must not exceed 12 bar. The ratio of permeate flow rate to drain flow rate must not exceed 0.75.
  • It is advisable to supply influent water using a feed water tank and pump, and to deliver permeate using permeate tank and pump.
  • Keeping a repair kit is advised.

Cookies

This Platform uses first- and third-party cookies to improve your experience and our services, analyzing browsing within the Platform. By continuing to browse you are accepting their use.

You can find more information or learn how to change the settings in our Cookie Policy.

By continuing to browse you are accepting their use.

Also you confirm that you have read and understood the Privacy Policy.